[AudioI] Result of test with Audacity VU meter

[Celia Wilkins]

Hi Matt -
I'm on a Raspberry Pi 4 model B, using Raspbian OS 10 (buster), and my
asound.conf, config.txt, and .asoundrc files are attached. The octo is
definitely being detected by cat /proc/asound/cards. After testing the
input pins with the Audacity VU meter, I have found that only the front
four or five input pins (as well as the output pins) give any signal, if
you're looking at the Pi with the input breakout board on the right. My
colleague is having the same problem. A picture of the setup is also
attached. Is this a hardware problem? Thanks!
CW
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.audioinjector.net/pipermail/people/attachments/20210405/d963ea2e/attachment-0001.htm>
-------------- next part --------------
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
dtparam=i2s=on
dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
#dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d
# enable the AudioInjector.net sound card
dtoverlay=audioinjector-addons
-------------- next part --------------
A non-text attachment was scrubbed...
Name: asound.conf
Type: application/octet-stream
Size: 409 bytes
Desc: not available
URL: <https://lists.audioinjector.net/pipermail/people/attachments/20210405/d963ea2e/attachment-0002.obj>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: .asoundrc
Type: application/octet-stream
Size: 150 bytes
Desc: not available
URL: <https://lists.audioinjector.net/pipermail/people/attachments/20210405/d963ea2e/attachment-0003.obj>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: IMG_0267.jpg
Type: image/jpeg
Size: 2757988 bytes
Desc: not available
URL: <https://lists.audioinjector.net/pipermail/people/attachments/20210405/d963ea2e/attachment-0001.jpg>